5v

Search

You can find the results of your search below.

MySensor board @projects:electronics
3 Hits, Last modified:
ce^Package^Parts^eBay search^ |1|ARDUINO_MINI_PRO_5V|ARDUINO_MINI_PRO_5V|IC1|New Pro Mini atmega328 5V 16M Replace ATmega128 Arduino Compatible Nano| |1|NRF24L01|NRF24L01|IC2
IO Board @projects:electronics
2 Hits, Last modified:
,B3 on U21|RESET DRV |B2 ^#|A2 |SD7 |A1 on U24| |+5V|+5 V dc |B3 ^#|A3 |SD6 |A2 on U24| |n/c|IRQ 9 |B4... B1 on U22| |n/c|BALE |B28^#|A28|SA3 |A4 on U22| |+5V|+5 V dc |B29^#|A29|SA2 |A3 on U22| |n/c|OSC |B30^
Barometric Pressure sensor @projects:electronics
2 Hits, Last modified:
heet}} MAX3221 is the wrong chip, it only does +-5V 232 signals, I will need to remove and add the MA... AX233CPP Breakout board ==== ^Wire^Function^ |Red|5V| |Yellow|RX (Data from computer)| |Blue|TX (Data
Optical Mouse @projects:electronics
2 Hits, Last modified:
on^Pin^ |Red|Ground|Gnd| |Black|SCLK|RC3| |Orange|5V Power|5V| |Yellow|SDIO|RC4| {{:projects:electronics:opticalmouse:adns-2051.pdf|}} ===== Pixart PAN
Panel Meter Interface @projects:electronics
2 Hits, Last modified:
===== 94 Ohms coil resistance 5K Ohm resistor @ 5V = 1mA ==== MCP4821 ==== ^Pin No.^Symbol^Function^ |1|Vdd|Supply (2.7 to 5.5V)| |2|CS|Chip Select| |3|SCK|Serial Clock Input| |
Notes
1 Hits, Last modified:
Sensor| |IC2|LM358N|Dual Opamp| |IC3|LM78L|Vreg, 5V| |BP1|{{:notes:tdk_chs-ugr_datasheet.pdf|TDK CHS-
Wishlist
1 Hits, Last modified:
Package Tracker]] [[http://www.sparkfun.com/commerce/product_info.php?products_id=8999|5V DC-DC reg]]
Camera Flash Control @projects
1 Hits, Last modified:
|White|F2|flash ready signal / data|2 Hz signal 1-5V (0V when charging)|2| |Black|F3|TTL OK signal / c
Fixing a Garmin USB charging cable @projects
1 Hits, Last modified:
iusbpinout.png|Miniusb Pinout}} ^Pin^Function^ |1|5v Power| |2|n/a| |3|n/a| |4|17.3K to Ground| |5|Gro
WET610N @projects
1 Hits, Last modified:
2.5V Vdd Output: 2.531
50 Amp 5 Volt Power Supply @projects:electronics
1 Hits, Last modified:
500|}} Need a 208.76 ohm, 1% resistor to set the 5V output. Right now I'm using a 500 ohm potentiomet
GPS @projects:electronics
1 Hits, Last modified:
eive, CMOS/TTL| |8|GND|Ground, Power and Signal| 5V @ 200mA, less than 100 mV of ripple noise, peak t
Prototyping breadboard idea @projects:electronics
1 Hits, Last modified:
readboard idea ====== * Polyswitch * 12V * 5V * 3.3V * Serial level converter * Reset swi