====== DVG-1120 ====== 9600 Baud, 8N1 {{:electronics:voip:dvg1120s_manual_210.pdf|}} ===== Serial Port Pinout ===== {{:electronics:voip:rj11m.gif|}} ^RJ9^Colour^Function^Pin^ |1|Blk|Ground| |2|Red|RX (Data to Computer)| |3|Grn|TX) |4|Yel|?| ^Colour^Function^-^ |Blk|| |Red|TX (from computer)| |Grn|RX (To Computer)| |Yel|Ground| ===== Commands ===== ^Command^Function^ |spy 16 *|Show Debug info for SIP| |nwdbg bridge off|Disable bridge mode| |dhcpserv state on|Enable DHCP server| == help == MXP Debug Application Command List Command Description / Repeat Last Command ? Displays Command Help Table help Displays Command Help Table dbgcmd Handles dbgcmd "command arg arg ..." syntax ----------------------------- User Commands activate Activate Current Config break Debug Breakpoint ccu CCU Commands commit Commit config to flash da DSP Allocator Commands dcm DCM commands dhcpserv DHCP Server Commands dim DIM Testing Commands dlm DLM Testing Commands dsp DSP Runtime commands (Debug) dspsim DSP Simulation Comands dump Display memory: exe execute function:
flash Flash util commands fxo FXO Commands ipfilter IP Filter Commands memstat Memory Usage Information mod Modify bytes: .. nat NAT Commands nw NWIF Debug Commands nwdbg NWDBG Debug Commands ping PING Debug Commands pppoe PPPoE Commands pstn PSTN Debug Commands route Route Commands set Set System configuration show Show system Configuration sigsim Signaling Simulation Comands sip SIP Commands snmp SNMP Client Commands spy Set/Display Spy levels: [ ] tftp TFTP Client Commands tiu TIU Debug Commands wait wait xgcp XGCP commands == dhcpserv == DHCP Server Commands: --- DHCP Server Common Commands--- dhcpserv cfg - List all configuration information of DHCP Server. dhcpserv dump - Dump IP Pools of DHCP Server. dhcpserv help - Displays all DHCP Server Commands. --- DHCP Server Dynamic IP Pool Commands --- dhcpserv startip - Set Start IP Address of Dynamic IP Pool. dhcpserv range <0~255> - Set IP Range(Number) of Dynamic IP Pool. dhcpserv subnet - Set Subnet Mask of Dynamic IP Pool. dhcpserv gw - Set Default Gateway of Dynamic IP Pool. dhcpserv configdns on|off - Set Get DNS auto or manual . dhcpserv dns - Set DNS Server of Dynamic IP Pool. dhcpserv wins - Set WINS Server of Dynamic IP Pool. dhcpserv domain - Set Domain Name of Dynamic IP Pool, e.g. 'dlink.com.tw'. dhcpserv lease <0~720> - Set Lease Time(in hour) of Dynamic IP Pool, 0 means infinity. dhcpserv state [on|off] - Set Administration State of Dynamic IP Pool. --- DHCP Server Static IP Pools Commands (4 pools,id:1~4) ---. dhcpserv static [id] cfg - List configuration information of [pool id] Static IP Pool. dhcpserv static [id] ip - Set IP Address of [pool id] Static IP Pool. dhcpserv static [id] mac - Set MAC Address of [pool id] Static IP Pool. dhcpserv static [id] subnet - Set Subnet Mask of [pool id] Static IP Pool. dhcpserv static [id] gw - Set Default Gateway of [pool id] Static IP Pool. dhcpserv static [id] dns - Set DNS Server of [pool id] Static IP Pool. dhcpserv static [id] wins - Set WINS Server of [pool id] Static IP Pool. dhcpserv static [id] domain - Set Domain Name of [pool id] Static IP Pool, e.g. 'dlink.com.tw'. dhcpserv static [id] state [on|off] - Set Administration State of [pool id] Static IP Pool. == nwdbg == nwdbg un - set the username nwdbg pw - set the password nwdbg serial - set the serial number nwdbg feature - set the 4-byte, hex format feature words nwdbg system reboot - reboot the device nwdbg save changes - save all changes and reboot the device nwdbg factory reset - set the flash data to default value, - and reboot the device nwdbg nmm reset - reset the NMM to default value, - but keep CA, RGW,... not change, - then reboot the device ---------------------------------------------------------------------------- nwdbg lifeline [on|off] - turn on/off lifeline nwdbg lifeline prefix - set the lifeline prefix nwdbg country - set the system country code nwdbg gain - set the receive and transmit gain nwdbg slic <0|1> - 0:standby, 1:active nwdbg dtmf_relay <0|1> - 0:off, 1:on ---------------------------------------------------------------------------- nwdbg tone dump - dump tone table. nwdbg tone cnt - set number of tone elements. - TONE NAME : busy,ring,cong,dial,sdial,dial2,out,addr,dconn,offn,offa, dial3,offon,wail,reorder,echo1,echo2,rdconn. - CNT : min 0, max 6. nwdbg tone - set tone element. - ELEMENT : - ROW : the row of table, min 0, max 5. - N : the number of frequency in this ROW, min 0, max 4. - F1, F2, ..: frequency, in Hz - AMP1, ....: amplitude, in 1/10 dB unit, min -800, max 30. - DUR : the duration, in ms, of the tone element to be transmitted. min 0, max 0xffffffff. - Here is a tone definition, Cadence : 500ms-ON, 500ms-OFF Frequency : 480Hz, 620Hz Level : -2.4dB Then the table will be : ROW | N f1 amp1 f2 amp2 f3 amp3 f4 amp4 dur ----+------------------------------------------------------- 0 | 2, 480, -240, 620, -240, 0, 0, 0, 0, 500 (ON) 1 | 0, 0, 0, 0, 0, 0, 0, 0, 0, 500 (OFF) CNT is 2. ---------------------------------------------------------------------------- nwdbg mac - set device mac address to XX:XX:XX:XX:XX:XX nwdbg ip - set to DHCP, BOOTP or Manual(fixed ip) mode if Manual mode : nwdbg ip - set device ip to d.d.d.d nwdbg mask - set device subnet mask to d.d.d.d nwdbg gw - set device default gateway to d.d.d.d nwdbg lan_ip - set LAN IP Address. nwdbg lan_mask - set LAN IP MASK. nwdbg lan_mac - set device LAN mac address to XX:XX:XX:XX:XX:XX. nwdbg wan mtu [1500-576] - set the mtu size nwdbg ether_status - display the current linking status of LAN and WAN ports. nwdbg host - set the host name nwdbg web port - set the web port number from 1024 to 29999 and 80 ***** reboot the device to make the above setting activate ***** ---------------------------------------------------------------------------- nwdbg ca - set the notify entity, the format can be : - [domainName|ip]:port - [domainName|ip] nwdbg rgw - set the gateway raw name nwdbg proxydns [disable|enable]- set the proxydns state nwdbg proxydns [manual|auto]- set the proxydns auto/manual nwdbg proxydns server_ip [servip]- set the proxydns ip nwdbg dns [DNS IP] - set the dns ip nwdbg dns [disable|enable] - set the dns state ***** use save-changes command to activate the above setting ---------------------------------------------------------------------------- nwdbg bridge [on|off] - on/off software bridge nwdbg bridge 0 [10 to 60] - 10M rx watermark nwdbg bridge 1 [26 to 60] - N-way rx watermark ---------------------------------------------------------------------------- nwdbg [UPnPOn|UPnPOff] -on/off UPnP nwdbg gap_time - Inter-Packet Gap Time [0 to 250] msec. 0: disable ---------------------------------------------------------------------------- nwdbg [config|mac|ip|...] - show [all|mac|...] configuration == show == Show Commands: show version show coding [prof_id] show tcid [tcid] show tlevels [tcid] show tstat [tcid] [clear] show vpstat [tcid] [clear] show rxtxstat [tcid] [clear] show errstat [tcid] [clear] show modemstat [tcid] [clear] show modemrelaystat [tcid] [clear] show faxstat [tcid] [clear] show fax_call_stat [tcid] [clear] show call_record [tcid] show ec_debug_stat [tcid] [clear] show ecpath_coeff [tcid] [filter: 0=BG, 1=FG, 2=Srch] [start_index] [no_coeffs] show dsp_version [dsp] show aal2_prof OK