Search
You can find the results of your search below.
Fulltext results:
- Formatting Syntax @wiki
- t. You should use forced newlines only if really needed. ===== Links ===== DokuWiki supports multiple... glish language file * Copy only the strings that needs to be modified */ $lang['js']['nosmblinks'] = '... be shown before the video has started. That image needs to have the same filename as the video and be ei... can be done to produce any kind of HTML, it just needs to be added to the [[doku>entities|pattern file]
- Lenovo T530 Laptop WiFi upgrade @projects
- (Under frame), according to various resources, I need to flash the 4MB chip. There is also another flas... ains the bios settings and password which I don't need to touch. There are forums for whitelist removal... m unable to make it work myself. (Also, I'd still need to figure out the bios reading and writing) VID:
- Fluke 189/187/89-IV/87-IV Remote Interface Specification @reference
- DB9 connector. The PC RS-232 communications port needs to control these two signal lines via software, ... the PC. The DB9 connector on the IR adapter cable needs to have the following lines with the following v... adapter cable for the Fluke 189 and 187 does not need any special control of its signal lines. It can b
- NeXt Cube @vintage
- rd If you've forgotten the root password, you'll need to follow the following procedure to reset it so ... m has started and dumps you at a root prompt, you need to make sure NetInfo and other services get start... DB19 male/female connectors). The following wires need to be connected with the VGA cable (DB15 connecto
- 405nm Laser Diode @projects
- ltraviolet really. I made a driver board and just need to finish the heatsink and mount it in a case. I ... llimating lens intended for a red laser diode. I need to get a quote on a proper lens such as this one
- Welcome to your new DokuWiki @wiki
- s ===== Create your first pages ===== Your wiki needs to have a start page. As long as it doesn't exis... on, follow that link and create the page. If you need help with using the syntax you can always refer t
- Barometric Pressure sensor @projects:electronics
- ressuresensor:mpx5010.pdf|}} ==== MAX3227 ==== I need to order the 296-19829-1-ND {{:projects:electroni... wrong chip, it only does +-5V 232 signals, I will need to remove and add the MAX3227 {{:projects:electr
- SD GPS Track Logger @projects:electronics
- onics:microchip#icsp_connector|ICSP Connector]] Need a PIC18 chip with more memory, I'm using the PIC1... not working. Might be software or hardware, I'll need to check it on a digital oscilloscope. {{:proje
- LCD Display @arduino
- crystal/wiki/Home|New LiquidCrystal]] library * Need pull-up resistors on SDA and SCL lines (A4 & A5 p
- Intersil Light Sensor @electronics
- nsor ====== {{:electronics:isl29001_datasheet.pdf|ISL29001}} - Datasheet * Need a 100kΩ 1% Resistor
- Water meter monitoring @esphome
- ===== This is still a work in progress, and will need some customization for your specific installation
- Gel Candles @projects
- rinted text (No labels, nothing that can burn) is needed. I also have some [[http://www.bawls.com/|Bawls
- Transmission Holograms @projects
- ansmission Holograms ====== ===== Exposure ===== Need <m>110 \mu Jcm^-2</m> on holographic plate. Meas
- 50 Amp 5 Volt Power Supply @projects:electronics
- onics:50a5vpowersupply:50a5vpwrsupply.jpg?500|}} Need a 208.76 ohm, 1% resistor to set the 5V output. R
- DGPS-11 Beacon Receiver @projects:electronics
- sdale Semiconductor]] now produces the chip and I need to find a supplier. Or buy it off of eBay for $30