Search
You can find the results of your search below.
Matching pagenames:
Fulltext results:
- NeXt Cube @vintage
- ith the VGA cable (DB15 connectors): VSync: Next pin 8, connect with VGA pin 14 HSync: Next pin 9, connect with VGA pin 13 Video: Next pin 10, connect with the RGB VGA pins 1,2,3 GND: Next pins 13
- 405nm Laser Diode @projects
- nting the laser in. * 405nm (Blue) Laser * 3 pin * 3.6mm diameter ===== Power Measurements ====... ===== {{:projects:405nmlaser:ldpinout.gif?100|}} ^Pin^Description^ |1|Anode(+)| |2|Case Ground| |3|Cath... 405nmlaser:img_0747.jpg?200|Red Diode}} ====== 4 pin Laser Diode ====== {{:projects:405nmlaser:ir_visi... ser diode driver notes ====== Require a DB9 Male ^Pin # ^Description ^ |1,2 |Interlock Shorting jumper
- Magtek Card reader @projects:electronics
- resent all pins are high. When a card is present pin 5 goes low and remains that way for 140ms after the entire card has been read. ==== Pin Information ==== ^Pin ^Color ^Signal^ |1|Red|Vcc| |2|Black|GND| |3|Orange|DATA| |4|Brown|STROBE| |5|G
- Fluke 189/187/89-IV/87-IV Remote Interface Specification @reference
- e following voltages applied: * DTR disabled - pin 4 with -3 to -12 volts (or tied to pin 5, Ground, will work also) * RTS enabled - pin 7 with +3 to +12 volts ===== Communication Protoco
- GPS @projects:electronics
- aicom HI-406BT ====== 19200bps, 8N1 Serial Data ^Pin^Wire^Description^ | |Blue|3V<sub>pk-pk</sub> seri... data I/O functions are integrated into a single 8-pin header 0787connector, J3. The J3 connector uses 0... nch (3.8 mm) pins on 0.0787 inch (2 mm) spacing ^Pin #^Function^Description^ |1|TXD 2|Port 2 transmit,
- Vindriktning @esphome
- ndriktning ====== Ikea air particulate sensor RX pin on ESP-01S header is pin 5 ====== Serial testing ====== Configure serial port: <code bash>stty -F /de
- C.H.I.P Computer @projects
- e & current * "ACIN" [[http://docs.getchip.com/#pin-headers|(Pin 2 of U13)]] voltage & current * and more... ==== Examples ==== <code> root@chip:~# ax
- Lenovo T530 Laptop WiFi upgrade @projects
- ering up a portion via the CH341A programmer. - Pin 1 of the test clip is the wire with the Red strip... etooth (Which involves placing kaptop tape over a pin) ==== Current Whitelist ==== TODO: Revise list a
- Panel Meter Interface @projects:electronics
- 5K Ohm resistor @ 5V = 1mA ==== MCP4821 ==== ^Pin No.^Symbol^Function^ |1|Vdd|Supply (2.7 to 5.5V)|... ut BCF TRISC,SDA ; SCK as Output ;Set initial pin states BSF PORTB,RB1 ;Chip Select, active low
- Barometric Pressure sensor @projects:electronics
- ts:pic18f1320.pdf|PIC18F1320 Datasheet}} RX on pin 3 TX on pin 2 <code> Power ON 98.97 kPa, 742.3 Torr ; 0814,0521 98.97 kPa, 742.3 Torr
- IO Board @projects:electronics
- ====== Pinout ====== ^Relay board^Signal Name^Pin^#^Pin^Signal Name^ ||Gnd|Ground |B1 ^#|A1 |-I/O CH CK|I/O channel check; active low=parity error| |A3,
- Optrex IM50240 Display @projects:electronics
- :projects:electronics:hd44100r_datasheet.pdf|}} ^Pin^Function^Notes^ |1|DL1|| |2|CL1|| |3|CL2|| |4|M|5
- Serial Converter @projects:electronics
- Uses no external caps ===== Cable Pinout ===== ^Pin ^Wire Colour ^Description ^ |1 |N/C | |2 |Black |
- SD GPS Track Logger @projects:electronics
- ICtail Daughter Board Info Sheet}} ^Function^I/O^Pin^Description^ |SCK|O|RB1|SPI Clock Out| |SDI|I|RB0