Search
You can find the results of your search below.
Fulltext results:
- NeXt Cube @vintage
- ith the VGA cable (DB15 connectors): VSync: Next pin 8, connect with VGA pin 14 HSync: Next pin 9, connect with VGA pin 13 Video: Next pin 10, connect with the RGB VGA pins 1,2,3 GND: Next pins 13
- 405nm Laser Diode @projects
- nting the laser in. * 405nm (Blue) Laser * 3 pin * 3.6mm diameter ===== Power Measurements ====... 9.0| |4.4| |50.0|4.41|5.7| |60.0|4.52|9.8| ===== Pinout ===== {{:projects:405nmlaser:ldpinout.gif?100|}} ^Pin^Description^ |1|Anode(+)| |2|Case Ground| |3|Cath... 405nmlaser:img_0747.jpg?200|Red Diode}} ====== 4 pin Laser Diode ====== {{:projects:405nmlaser:ir_visi
- DVG-1120 @electronics:voip
- oip:dvg1120s_manual_210.pdf|}} ===== Serial Port Pinout ===== {{:electronics:voip:rj11m.gif|}} ^RJ9^Colour^Function^Pin^ |1|Blk|Ground| |2|Red|RX (Data to Computer)| |3|... nwdbg NWDBG Debug Commands ping PING Debug Commands pppoe PPPoE Commands pstn PSTN Debug Command
- Magtek Card reader @projects:electronics
- ack 2 2.7 to 5.5VDC When no card is present all pins are high. When a card is present pin 5 goes low and remains that way for 140ms after the entire card has been read. ==== Pin Information ==== ^Pin ^Color ^Signal^ |1|Red|Vcc| |2|Black|GND| |3|Orange|DATA| |4|Brown|STROBE| |5|G
- GPS @projects:electronics
- aicom HI-406BT ====== 19200bps, 8N1 Serial Data ^Pin^Wire^Description^ | |Blue|3V<sub>pk-pk</sub> seri... data I/O functions are integrated into a single 8-pin header 0787connector, J3. The J3 connector uses 0.150 inch (3.8 mm) pins on 0.0787 inch (2 mm) spacing ^Pin #^Function^Description^ |1|TXD 2|Port 2 transmit, CMOS/TTL| |2|Pr
- Stepper motor driver @projects:electronics
- r:back_con.jpg?400|}} ^DB9^Connection^ |1|L298-Pin14-Output 4| |2|L298-Pin13-Output 3| |3|L298-Pin3-Output 2| |4|L298-Pin2-Output 1| |5|Ground?| |6|Logic?| |7|Logic?| |8|Logic?| |9|Logic?| ====== Ste
- MBED @electronics
- ====== MBED ====== {{:electronics:mbed:pinout.png|}} ===== Ethernet ===== Magjack - {{:electronics:mb... F Datasheet}} {{ :electronics:mbed:ethernet.png|Pinout}} ^Pin^mbed^ |P1|RD+| |P2|RD-| |P3|Vcc| |P4|n/c| |P5|n/c| |P6|Vcc| |P7|TD+| |P8|TD-| <HTML><BR CLE
- Fluke 189/187/89-IV/87-IV Remote Interface Specification @reference
- e following voltages applied: * DTR disabled - pin 4 with -3 to -12 volts (or tied to pin 5, Ground, will work also) * RTS enabled - pin 7 with +3 to +12 volts ===== Communication Protoco
- IO Board @projects:electronics
- ors, rated for 5 to 240 Volts, AC or DC. ====== Pinout ====== ^Relay board^Signal Name^Pin^#^Pin^Signal Name^ ||Gnd|Ground |B1 ^#|A1 |-I/O CH CK|I/O channel check; active low=parity error| |A3,
- Temperature sensing devices @projects:electronics
- Accurate, 16-Bit Digital I2C Temperature Sensor ^Pin^^Wire Colour^ |1|SCL|Yellow| |2|SDA|Blue| |3|A0|G... |8|Vdd|Red| |7|Gnd|Black| Need 0.1uF Cap between pins 7 & 8 {{:projects:electronics:adt7410_pinout.png?600|}} From [[http://www.analog.com/en/sensors/d
- Vindriktning @esphome
- ndriktning ====== Ikea air particulate sensor RX pin on ESP-01S header is pin 5 ====== Serial testing ====== Configure serial port: <code bash>stty -F /de
- C.H.I.P Computer @projects
- e & current * "ACIN" [[http://docs.getchip.com/#pin-headers|(Pin 2 of U13)]] voltage & current * and more... ==== Examples ==== <code> root@chip:~# ax
- Camera Flash Control @projects
- amera Flash Control ====== {{:projects:flash:iso_pinout.jpg|}} ^Cable^Shoe^Function?^Voltage^Wire^ |... ony-minolta/flashcomp_techref.php#oldshoe|Hotshoe Pinout]] [[http://www.snowcat.de/flashcontroller/|
- Fixing a Garmin USB charging cable @projects
- ble ====== {{ :projects:miniusbpinout.png|Miniusb Pinout}} ^Pin^Function^ |1|5v Power| |2|n/a| |3|n/a| |4|17.3K to Ground| |5|Ground|
- Lenovo T530 Laptop WiFi upgrade @projects
- ering up a portion via the CH341A programmer. - Pin 1 of the test clip is the wire with the Red strip... etooth (Which involves placing kaptop tape over a pin) ==== Current Whitelist ==== TODO: Revise list a