Search

You can find the results of your search below.

C.H.I.P Computer
6 Hits, Last modified:
C~~ ====== C.H.I.P Computer ====== ===== Headless Setup ===== - Connect CHIP to your Linux computer v... C registers, everything else is only reading ==== Setting VBUS current limit ==== * i2cset -y -f 0 0x34 0x30 0x60 # 900mA VBUS current limit (Default) * i2cset -y -f 0 0x34 0x30 0x61 # 500mA VBUS current limit
Panel Meter Interface @projects:electronics
3 Hits, Last modified:
clk macro BSF PORTC,SCK BCF PORTC,SCK endm ;Setup direction BCF TRISB,RB1 ; RB1 as Output BCF ... SDO as Output BCF TRISC,SDA ; SCK as Output ;Set initial pin states BSF PORTB,RB1 ;Chip Select, ... 1,F,A RLNCF DAC+1,F,A RLNCF DAC+1,F,A RLNCF DAC+1,F,A BSF PORTB,RB1 ; Set CS high return </code>
Tire Pressure Sensor Code @projects:electronics:tirepressuresensor
3 Hits, Last modified:
** ; VECTORS org 0x000000 ; Processor reset vector (power-up here) nop nop ; First... 2C_AckWait movf _Error,F,A ; If _Error is set, change output to --- btfsc STATUS,Z goto n... ' ' Skip_Blank movf _Error,F,A ; If _Error is set, change output to --- btfsc STATUS,Z goto N
Transmission Holograms
2 Hits, Last modified:
ttp://picasaweb.google.com/photonicsguy/HolographySetup">Holography Setup</a></td></tr></table> </html>
Lenovo T530 Laptop WiFi upgrade
2 Hits, Last modified:
ory chip on the underside which contains the bios settings and password which I don't need to touch. T... 79E0EDD7-9D1D-4F41-AE1A-F896169E5216 at header-offset 0h - Go to PE32 Image section, right click,
IO Board @projects:electronics
2 Hits, Last modified:
l check; active low=parity error| |A3,B3 on U21|RESET DRV |B2 ^#|A2 |SD7 |A1 on U24| |+5V|+5 V dc |B3 ^... 1|IC GATE OR QUAD 2INP| |U38|74HC74AM|1|F/F W/CLR&SET DUAL D| |U25|74HC4538M|1|IC MULTIVIBRATOR DUAL HS
405nm Laser Diode
1 Hits, Last modified:
projects:405nmlaser:p1020543_cropped.jpg?200|Same setup, just with lights on}} {{:projects:405nmlaser:i
50 Amp 5 Volt Power Supply @projects:electronics
1 Hits, Last modified:
ply.jpg?500|}} Need a 208.76 ohm, 1% resistor to set the 5V output. Right now I'm using a 500 ohm pote
MySensor board @projects:electronics
1 Hits, Last modified:
t the silkscreen for the I2C connector * Counterset the breakaway tabs slightly * Verify pricing on
Optrex IM50240 Display @projects:electronics
1 Hits, Last modified:
ptrex IM50240 Display ====== Hitachi HD44100H Chipset {{:projects:electronics:hd44100r_datasheet.pdf|}
Prototyping breadboard idea @projects:electronics
1 Hits, Last modified:
==== * Polyswitch * 12V * 5V * 3.3V * Serial level converter * Reset switch * ICSP port
USB Serial Adapter @projects:electronics
1 Hits, Last modified:
jects:electronics:usbserial:pl2303_xp2kme98driver_setup.zip|Local copy}} 3.3V Logic ^Wire^Function^ |Y